AUSTRALIA

The EN17235 Standard and Fallprotec Products

The EN17235 Standard and Fallprotec Products

The new European standard EN17235 was published in the Official Journal of the European Union on 9 February 2026 (Commission Implementing Decision (EU) 2026/284). It will replace EN795 (for permanent anchors) and EN517 from 9 August 2027. All European standards that could conflict with it will then be withdrawn.

Structure of the standard

The new standard is divided into Kits, with a structure similar to the “Types” of EN795, and Classes, which determine the number of simultaneous users according to the dynamic force supported.

List of Classes

  • Class 1: 9 kN (1 user)

  • Class 2: 10.5 kN (2 users)

  • Class 3: 12 kN (3 users)

  • Class 4: 13.5 kN (4 users)

List of Kits

  • Kit A – single anchor

  • Kit B – safety hooks

  • Kit C – horizontal cable

  • Kit D – horizontal rail

Timeline

The coexistence period runs from 9 February 2026 to 9 August 2027; during this period, products can already be CE marked to EN17235. From 9 August 2027, EN17235 becomes mandatory and EN517 will be withdrawn (EN795 remains in use for temporary anchors). Important point: the standard is not retroactive. Existing EN795 installations remain valid, subject to the required inspections. The Fallprotec range is being recertified to EN17235.

Why this change?

EN795:2012 improved height safety requirements, but it had a major weakness: for Types A, C and D (single anchors, flexible lifelines and rigid rails permanently fixed to the building), it was not linked to any European directive or regulation. Because these devices remain on the structure, they are not considered personal protective equipment: only Types B and E were covered by the PPE directive. For permanent anchors, EN795 was an “orphan standard”: no CE marking and no common legal framework across Europe.

EN17235 closes this gap by bringing permanent fall protection anchors within the scope of the Construction Products Regulation (CPR). Anchor points and horizontal lifelines are now treated as construction products, and CE marking is back for them, backed by a Declaration of Performance.

The aim is also to harmonize requirements across Europe, which until now have been fragmented by national rules, and to create a common framework in all EU countries. This follows the European principle of free movement with common rules, avoiding trade barriers. This unified standard is a real opportunity within Europe, but also beyond it: EN795 was recognized worldwide, and the stringent requirements of EN17235 provide a quality label that applies in any country.

What “EN17235 certified” really means

The certification covers the anchors, the fixing and the substrate, the latter being the real novelty compared with EN795. EN17235 requires the lifelines and their fixing interface to be tested on a roof mock-up; for fragile structures, these mock-ups measure 3 × 3 m. Testing the lifeline together with the roof, under the supervision of a notified body, is a complex, time-consuming and costly process. Certification also includes a Declaration of Performance detailing in particular mechanical strength, durability and watertightness, annual audits by the notified body, and CE marking.

The forces are lowered. Because EN17235 characterises the fixing brackets and their interface with the structure much more thoroughly, the CEN committee considered that the test forces could be reduced. The safety coefficient has also changed: EN795:2012 applied a factor of 2 to the 6 kN maximum arrest force, hence a 12 kN static test for a single user (13, 14 and 15 kN for additional users under the multi-user technical specification). EN17235 is based on the Eurocodes and applies a global safety factor of 1.5, which gives the 9 kN of Class 1 and the class values from 10.5 to 13.5 kN.

CE marking under the CPR is far more than a logo: it is a guarantee of quality. It confirms that the performance declared by the manufacturer has been verified by an independent notified body, under the most demanding assessment system of the regulation (System 1+), and that production remains under this body’s control over time. This is why CE marking is recognized well beyond the borders of the European Union.

Annual audits and random tests. As is already the case for vertical lifelines, which fall under EN353-1 and the PPE Regulation, anchor points and horizontal lifelines certified to EN17235 will be audited annually by the notified body, with random tests on production samples. Every system leaving the factory must perform like the one that was certified.

What the standard does not cover

EN17235 does not cover every roof. Steel roof sheets thinner than 0.5 mm, fixings by nails and fixings through the roof waterproofing system are outside its scope. For these cases, and for roofs not covered by the tested configurations, Fallprotec offers internal validation tests with a dedicated engineering report.

What impact on other standards?

EN17235 will be adopted in place of national standards in the European Union. In the United Kingdom, it will be implemented as BS EN17235.

An EN17235-2 standard is planned. It will not lead to CE marking, but will provide further explanations and cover design, planning and inspection (similar to BS 7883 in the United Kingdom), as well as additional requirements for rope access, work restraint and work positioning. A notable change is expected for rope access: anchors would be rated at 9 kN, instead of the 15 kN currently required by IRATA and British standards.

Where do things stand today?

As of the date of publication of this document, no one is yet certified to EN17235. Most manufacturers are in the process of testing to recertify their products..

Fallprotec’s position

Fallprotec took an active part in the CEN technical committee that drafted EN17235, and was therefore able to anticipate the changes, particularly for products that were then in the R&D phase. No major redesign of the range (lifelines, anchor points) is necessary. Only minor adjustments to dimensions and materials and updated marking are planned. Installations already in service require neither replacement nor modification.

For custom-made parts, a complete technical file will be provided: calculations, tests where required, a Declaration of Performance and enhanced traceability.

The Fallprotec products concerned: all variants of Securope, Securail Pro, SafeAccess, and the anchor points.